When for a short flight this morning to check the charging voltage coming from my alternator.  My digital multi-meter showed that the voltage at the battery was only 12.2 volts DC.  I should have seen right around 14 volts DC.  So I enjoy another 45 minutes or so of sight-seeing before returning to Oakdale to start troubleshooting.

I got back to the hangar and pulled the cowl.  My first check hit paydirt.  I found that the fuse between my voltage regulator and the battery was blown!  I drove down to Kragen Spruce and Specialty and purchased a few more 30A fuses.  I’ll replace the fuse tomorrow and recheck the voltage.

I had the day off of work so I decided to do more test flying.  What else?  Today’s flight went very well.  The only squawk is that my battery went dead again in flight.  This causes me to lose my tachometer and therefore I can’t do some portions of my testing.  So because of the dead battery I had to head back early.

I did do some stall testing today.  The results of which tell me I need to check out my airspeed indicator.  The results are, V_S0 = 38 MPH, and V_S1 = 50 MPH.  ??!  That’s a huge differential and means my airspeed indicator is not accurate at higher airspeeds.  But then I already knew that, this just confirms it.

By the way, for my non-airplane friends, V_S0 is the stall speed of the airplane with full flaps, V_S1 is the stall speed of the airplane without flaps.

I also took this opportunity to finish spraying a polyurethane UV blocker on my wings.  This will help them last longer.  That took most of the day but now my wings are water tight and protected from the sun.

Flew 1.4 hours this morning.  The weather is changing (again) so it was pretty bumpy.  Flew over the Oakdale Rodeo Parade and then around the area.  Practiced a few take-offs and landings back at Oakdale.  Decided that this morning’s fun was getting to be too much work so called it a day.

Yesterday I check my flight controls to see if I could locate the source of the aileron bumping I’m experiencing.  I couldn’t find anything loose or interfering in the aileron controls.  I tightened up the aileron cables that go from the stick to the cockpit overhead bellcrank as a precaution.  I also checked the rigging of the ailerons themselves.  I found that the left aileron was set a little high so  I adjusted the aileron to the correct angle.  Weather was not the best yesterday so I elected not to do any flight testing.

This afternoon it was a little windy but I decided that the winds met my minimums.  I took off and it was definitely a wild ride for the first 1000 feet of altitude but everything smoothed out to within acceptable bumpage.  I flew northwest towards Farmington.  As I was flying along I noticed my tachometer was swinging between normal RPM indications of about 5200 RPM to well over 6500 RPM.  I could hear that the engine was not changing pitch so I knew it had to be the gauge.  As I was mulling which gauge to switch to in my mind I noticed that I could no longer see the display on the radio.  Also the GPS started displaying it’s loss of power countdown.  I also recalled that on my last flight another pilot reported my radio as scratchy.  Hmmm… That helped me narrow the problem down to my battery not having enough of a charge to excite the alternator.  I think.  The rotax engine is a different animal than I’m used to.

I got back to the airport and the winds were really gusting at that point.  I carefully checked for other traffic (since I couldn’t use the radio) and entered the pattern.  Everything went well until I actually tried to land.  Then I found that I had developed a new landing technique.  This technique involved letting the upwind main wheel touch down, and then pick it back up.  Then letting the downwind main wheel touch down, and pick it back up.  Then let both wheels touch simultaneously, and again pick them back up.  THEN drop and pick back up all 3 wheels in rapid succession all the while maintaining poor directional control.  The problem?  I was distracted by the loss of power and failed to adequately control the airplane.  Did I break or bend anything?  No.  It was just one of those landings that made me SO happy the airport was deserted.  God is indeed good!

So two things to address before my next flight: the battery charging system, and my wind minimums.   God bless and happy landings.

I was able to locate the source of my flap malfunction.  The main cable that runs from my flap lever to where the cable splits into two is secured to a fitting on bulkhead behind the pilot’s seat.  The cable should have been safety wired to this fitting and was not.  This allowed the cable to slip out of the fitting.  I made sure the cable was securely seated into the fitting and then safety wired it in place.  This particular malfunction will NOT happen again.

Tonight I took advantage of a break in the weather to go for a quick late afternoon flight.  The conditions were perfect, a broken cloud layer at 7000 feet, mild temperatures, dappled sunlight shinning on the emerald green valley floor, and perfectly smooth air.  I practiced more take-offs and landings and just flew around the valley enjoying the scenery.  I should have been performing flight testing but I just couldn’t resist playing tourist instead.

I had a minor incident this evening as I was making the last landing of the day.  I was on short final, approximately 60 MPH and I pulled in the last notch of flaps.  About 5 seconds later I heard a loud noise, like a bang or pop, and then both flaps retracted themselves.  The flap lever was still in the fully deployed position in the last notch.  After I landed I was able to push the flap lever back down.  As I did so I heard some pops that sounded like metal threads slipping.  I examined the rod ends and everything looked okay.  I worked the flap handle again and everything seemed to work normally.  I fully deployed the flaps again and was not able to duplicate the problem by pushing up on the flaps manually.  I’m going to give the flap push-pull cables a more thorough examination tomorrow when the light is better.

I’ve got an email into the technical support folks at Rans to see if they have any ideas.

Flew for 1.7 hours today.  It was a pretty bumpy day but I just hung in there and endured the jolts.  It was such a nice day here in central California it would be a crime not to fly.  There were no squawks on the airplane today other than a dead battery which I discovered a few days ago.  I didn’t do any maneuvers or testing, just flew for enjoyment.  I also made two of my best landing today.  The second landing was well short of the first turnoff.  I would guestimate my rollout at about 400 feet or so.  Still quite long by back country standards but hey, I’m still knocking the rust off.

Flew for about an hour and a half today.  Mostly just pattern work.  I can’t believe how much the RV-4 spoiled me.  I have no problem with directional control, the problem is with the landing flare.  I keep flaring way too high.  Today I wore my old glasses and landings were much better.  These glasses will now live in the airplane.  I was able to make 10 landings, 9 of which were very good.  Still not landing at the top of my game but they are survivable.  I was going to continue until I started coming down with the flu (yeah, it came on quick) so I quit for the day.  On the bright side there were now squawks today.

Today I continued to battle a heavy left wing.  I almost have it completely gone.  I think one more adjustment ought to do it.  I also had to resynchronize my carburetors again today.    The engine seemed to be running a little rough in flight and on landing it quit.  Yes, I was already on the ground.  I advanced the throttle a little and it started right back up.  It did attract a lot of attention though.  Resynchronizing the carbs made the engine run much smoother and no more stoppage.

I’m still trying to get comfortable in the new plane. I’m pretty comfortable taxiing on the ground now.  I just have to get comfortable with the landings.  After a few landings I started doing a little better but still need a lot of practice.  I can tell you for sure that this gear is strong!  I’m coming in much too fast for this plane.  The last few landings were better.  A big part of the problem is getting my seat adjusted properly.  Once I have the seat and the landings dialed in, and no more heavy wing, I can start the testing in earnest.